Shoudn't it be 25%?
Current is not controlled here, resistance (aka the soldering iron) and voltage are.
Power = Voltage ^ 2 / Resistance. Double the voltage, that quadruples the power. So you only want to plug in 25% of the time to get the equivalent power of 120V.
But it might not melt at double power? Maybe the extra heat helps, I can't find a resistance/temperature curve for a soldering iron...
Source: EE dropout.
nnnNNEEEEEEERRRRRRRRRd!
Right you are. Oops.
Ok. I was acountless on lemmy for a long time, your comment made me finally register. Thanks!
So, yeah, with double the voltage you get 4x the power. But you you put 4 times the power at 50% of the time, you get only 2x the power. And the other half of the time, you get 0 power. On the average you get the same power output.
I had to think about it too, lol. This is an equation for DC/instantaneous power, and if you want to get into AC math, this is more like a square wave. Averaging the power out over time doesn’t necessarily work with the equation, as you figured out, as it doesn’t when you try to measure AC (sinusoidal) power by average voltage or whatever.
I sure hope someone will be fired for this obvious blunder
There are gas powered soldering irons that are essentially lighters with metal around the flame. Real life savers
There are also battery powered soldering irons.
Yes, and they actually have a working thermostat, so they aren't complete garbage to solder electronics with.
Gas powered soldering irons are great for soldering stuff like copper water pipes. But even soldering through-hole components with them is a pain in the ass due to the temperature instantly evaporating all your flux. Soldering SMD components is near impossible with them
Should have just left it in, and been able to get the soldering done twice as fast.
New manufacturing hack unlocked: Install 240v outlets at workstations and fire half of the workforce. Golden parachute and douchey, hand-wavey TED Talk, please!
Elon knows more about manufacturing than any other person on earth, he said
Finally, an usecase for USB irons!
I just got one, and it’s so practical with a PD battery bank. Can now solder inside or outside on my car/bike with zero hazzle
Don't they have switches?
Sounds like a cheap portable soldering iron, which just heats up to some roughly usable temperature whenever it's plugged in.
Textbook definition!
Ive seen some really cheap irons that have zero controls, you plug them in and they operate at max power. Basically a wood burning pencil, really.
An engineer that has a project to show off at a trade show will have will have both a power switch and a temperature control on their soldering iron.
I'm an engineer that's been in that sort of situation. If it's planned, you have the tools. Unfortunately, sometimes these things happen and it's not planned. At that point it's taken what you can get. A cheap fire stick will still do the job better than no fire stick.
Every one i've owned has and I get the cheap ones. I guess you can find them for under a dollar or something
I've only seen outlet switches in the UK, unless you plugged into a roof lamp outlet where the switch are by the entrance door, but then you need a plug like these (at least here in sweden)
I've had a similar experience as a child. I live in Germany and found this voltage switch on a hair dryer. My thoughts were like: Switching it to less couldn't possibly hurt, could it? Well it could. It was super efficient though but only for a few seconds before it self destructed.
They need a 1/4 duty cycle.
Person Wait Modulation.
I had the opposite problem, I brought a soldering iron from Europe to Canada, and despite using a step up transformer, it just couldn't get hot enough to melt the solder!
You should have used 200% duty cycle
Why plug and unplug? Doesn't the wall outlet have a switch?
Afaik it is a safety thing that is handled differently in different countries.
Uk and their colonised countries have this. The reason is that the fuses are in each plug. But no (or almost no) fuses in the power grid of the house. In Europe most countries have a single GFCI and several fuses for power grid sectors in a single place in the house where the power comes in.
I assume the switches on the power outlets are for turning off a switch because there is no GFCI in the house.
Reminds me of the time when I helped install some 120 VAC ceiling fans and the electrician* wired them to the 220 VAC line. They spun like a helicopter trying to take off.
*Worked for the local electric utility, we trusted him, foolishly.
Hey. If it works, it works.
Any port in a storm right?
So we've officially gone meta around here lol, we did it Lemmy!
Because the plug would fit the outlet, right?
There are a bunch of adapters you can buy that don't convert voltage, and it's pretty common for people to buy them by mistake.
and it's pretty common for people to buy them by mistake
Or even on purpose, for the many things that don't care (a lot of electronics, where it has a rectifier, are fine with 110-250V, 50-60Hz)
If someone knows how to solder, a different shaped plug isn't a big obstacle to them
