How do I shrink heatshrink in an explosion proof room?
How do I shrink heatshrink in an explosion proof room?
So I'm not sure what the right community for this is but I'm hoping yall can help. I'm a refrigeration service tech and recently I was tasked with replacing a sensor in a room used to store ethanol drums. Due to the nature of the room every device in it had to be rated explosion proof and I couldn't use any tools that could pose any risk of ignition (no heat gun, basically nothing with an electric motor, and definitely no open flames) while working in there. Normally when I splice wires I use heatshrink to cover the splice simply because it looks far more professional than electrical tape and it holds up better over time. However in this case I could not figure out any way of shrinking said heatshrink without posing a potential ignition hazard so I was stuck just wrapping the splice in tape. We do a lot of work for this company so I'm hoping to find a better solution for the next time I am in a similar situation.
So do any of you know any way to shrink heatshrink without posing an ignition hazard or am I stuck just using tape in those situations?
Maybe you can get your hands on cold shrink tubing? It's a rubbery tube stretched over a plastic frame thingy. You pull the frame out and the rubber shrinks down. No heat needed.
Posts like these are why Lemmy will surpass Reddit.
No ads, no bullshit. Thank you for posting this answer!I mean, I kinda did post an ad as an example, lol. But it was the most concise video I could find in like 30 seconds of looking! I am in no way shilling for whoever the company was. Any cold shrink brand will be more or less equivalent.
And you're welcome! I do like being helpful in areas I know things about.
I had never heard of that. Definitely going to look into it now though.
If you can't source that, you could use EPR tape
It's very expensive, but it would probably be the best option when you can't use heat.
In this case they can pass the cost onto the customer. The higher restrictions will always result in higher costs, so they're probably used to it.
I don't think there's any way to safely generate just enough heat for this to work without the ignition hazard. Heatshrink definitely looks nicer than tape but I think anyone will understand in this scenario.
Liquid electrical tape
Some PVC tubing will start to shrink around 70°C. Can you get boiling water to it fast enough before it cools?
A thermos might work!
There's an idea. As long as I'm using boiling water there will never be an ignition hazard because it will never go much above 100C. I could probably do something with a bit of water and quicklime to have an instant ignition free hotplate.
I'd need to figure out specifics and test it elsewhere of course but that is probably workable. The real question is if it's practical in the field. Either way it's something I'll probably try out at home just for fun.
Maybe some air-activated hand warmers? This page says they can get up to 70°C, although they average 57°C. Maybe that would be enough, using several?
There are explosion proof hot plates for lab work, you could get one of those or something similar.
Wait... How are you splicing the wires? Crimped butt splices?
In this situation it was butt splices. We almost never solder anything. We just need the butt splices sealed in case of condensation or dirt.
Ok, thought so. Another option is gel splice covers. They're a plastic box with waterproof goo in them to cover the connection. This is just one example, but there are plenty. Wago sells some specifically for their splice connectors. There are also some where you mix your own goo, but I've never seen or used them.
How about heating up a soldering iron outside, turnoff and unplug then take it in and use the residual heat?
I don't think a soldering iron would retain enough heat. I had considered warming something else up with a torch but any hot work anywhere in that site requires all sorts of permitting even where it's possible.
The options from other responses are better (gel, cold shrink tubing), but just for your edification, sand in a box can work as an extremely effective insulator for a short period. So heat up the soldering iron and stick it in a bed of sand in a box to take it in with you. Most of the heat won't escape the box, but it will spread through the tool, so you'll definitely want gloves.
Would self amalgamating tape work? You have to stretch it and wrap it fairly tight, which can be fiddlyvon small diameters, but it'll seal the joint and doesn't peel off and get nasty like electrical tape.