If a machine is never 100% efficient transforming energy into work because part of the energy is converted into heat, does it mean an electric heater is 100% efficient? [@showerthoughts@lemmy.world](h
If a machine is never 100% efficient transforming energy into work because part of the energy is converted into heat, does it mean an electric heater is 100% efficient? [@showerthoughts@lemmy.world](h
If a machine is never 100% efficient transforming energy into work because part of the energy is converted into heat, does it mean an electric heater is 100% efficient? @showerthoughts@lemmy.world
You know how you turn on an electric heater and the filament begins to glow? That is energy being converted to light, so not 100% efficient.
Doesn’t the light turn into heat anyway as soon as it’s absorbed?
and that light hits stuff and gets converted to heat.
That heat also powers certain chemical reactions happening on the surface of the hot wire. It’s not a lot of energy, but it’s still something. Light and sound tend to be converted back to heat at some point, but chemical transformations can be more stable, which would result in a tiny loss of efficiency.
Not all electric heaters use that kind of filament
This is true. I assume the ceramic heaters also emit light, just not in the visible spectrum.
Technically, yes. Even the internal resistances outside of the heating elements eventually radiate into the space. Since the purpose is space heating, it's not a waste product and they can be roughly considered 100% efficient.
The reason heat pumps are more efficient (i.e. around 300% or more) is not that they create more heat from the same amount of energy but because they concentrate and move existing heat from one source to another.
This is correct, but it's also, it's only 100% of the heat at that point in the circuit.
Technically, using natural gas to make electricity, then sending that electricity to an electric heater would be less efficient than burning that natural gas for heat at the source.
So it depends on where you start counting from.
True, and also the transmission losses between the power plant and your outlets are also factors. I just treated the question like a high school physics one where you're allowed to disregard air resistance. lol
If so that means moving a block of ice has negative heat efficiency. Sounds like nitpicking to me.
Yes, but a heat pump for heating is somwhere from 200% to 500% efficient.
Yes, except a heat pump is capable of being more than 100% efficient because the using the power to move heat around is more efficient than converting power directly to heat
but but muh thermodynamics
I get you are joking, but incase someone doesn't see the /s. As the top comment said it's easier to move heat around than creating it. Regardless if it's warmer or colder outside there's still energy there that we can use.
It's easier to move your clothes from the laundry basket to the wardrobe, than to go out and buy new clothes (or is it?).
Heaters sometimes produce a little light or sound, so not 100%, but very close.
The sound will eventually dissipate in the air as heat. The light will be absorbed into surfaces, like any other radiation, as heat. Still 100%, but with a couple extra stops along the way.
There's an interesting aspect of this that I have not seen mentioned yet. While this is true you are usually better off using your residential heater rather than an electric space heater because residential heaters are frequently over 100% efficient. That is, they deliver more heat for the energy expenditure than if you had converted the energy directly by redirecting ambient heat. Heat pumps are this same principle taken to the extreme.
But there's a flip side to that as well - if you've got heat pump heating your whole home but you only really need to heat 1 room, you may be "wasting" a good chunk of that bonus efficiency.
If you dont want certain rooms heated you close the doors to those rooms. And place the heater such that the airflow goes trough the rooms you want heated.
Also the house should be heated evenly unless you have really poor isolation and that should be addressed way before the minutia of heat pumps gets discussed.
But you can heat an area with 'better than 100% efficiency' if you use a heat pump and move heat from one place to another. Coefficients of performance (cop) of about 2.5 I think are pretty common, meaning if you put 100 watts into moving heat, the area will get 250 watts warmer.
Total amount of heat for the entire closed system does not increase over 100% of energy used to drive the heat pump. Like you said, you just moved heat around
tl;dr, yes If you want to watch a 20 minute video about it instead of 1 word answers, https://youtu.be/V-jmSjy2ArM
Here is an alternative Piped link(s):
https://piped.video/V-jmSjy2ArM
Piped is a privacy-respecting open-source alternative frontend to YouTube.
I'm open-source; check me out at GitHub.
Only in the sense of releasing heat into the surrounding environment. But for instance, an electric boiler is not 100% efficient because not all of the heat goes to the water. The heat that doesn't go to the intended recipient of the heat is treated as loss.
Yes. The end form of all energy is heat.
The problem is that heat is a high-entropy source of energy. As a result, the losses come when you try to convert all that delicious heat back into electricity (like with a steam turbine). The "efficiencies" only go one way (and I put efficiencies in quotes because, as you pointed out, getting energy into the form of heat is inevitable, whether that's the form you wanted or not)
I so want this to be true, but dont they produce radio waves?
I believe, in terms of work, that would be 0% efficient. You're basically going all-in on entropy.
You’re basically going all-in on entropy.
We all do that eventually.
I mean, if going all in on entropy is the goal, then space heaters are 100% efficient. If what you're trying to do is heat a room, they're also 100% efficient at turning electricity from the wall into heat energy in the room, but heat pumps are far better at that
Yes.
No by your logic it'd zero percent.
Efficiency is against a goal. You can't change goal post and make argument. Good try.
This is discussed in many places, but you are here, so let's do it... A heater that consists of a resistance element is turning nearly all of the electricity into heat. Around 100% efficiency. But if it has an LED and fan, then maybe 5% (or less?) of that electricity is used for those, so it's easy only 95% (or more?) efficient.
That is how those terms are defined in this context. How much heat is produced by a resistance heater using one watt? That's a known quantity, and we use it to compare against other heating sources.
And it makes sense to use this number if you are comparing to wood or gas or coal or oil heat, where some goes out the chimney, or to heat pumps, where things are a lot more complicated.
