Apologies, I know this isn't a woodworking question, but I don't know of a better place to ask about restoring a desk like this.
It's an oak desk, but it looks like there used to be a felt inlay, or maybe vinyl. The top of the desk has an inlay of plywood, with a small raised edge to the oak, of maybe 2 - 3mm. Staining or varnishing doesn't seem to be an option, as the style of the plywood doesn't match the rest of the desk, so I'm looking for ideas for the top.
Felt or vinyl would be the obvious options, but I'm hoping to hear some other ideas. It's going to be used as an office desk, with two computer monitors and a keyboard and mouse, but also for writing, mostly notes rather than anything serious.
The underside of the plywood has oak planks running from front to back, so there's the option of removing the plywood and putting in another piece of wood, but I don't want to spend too much if I can help it.
Does anyone have any suggestions or feedback please?
Thanks in advance :)
EDIT: Sorry if I'm a bit slow to reply tonight, I'm having a mad dash to tidy up and make room for the new desk. I've managed to plan everything backwards (again...)
Note for myself - the lip is 1mm and the plywood is 3mm, as best as I can tell without dismantling anything
Since you plan to use it for a computer desk have you considered neoprene or leather and just using the the whole surface as a mousepad.
Alternatively you could also go with some form of opaque tempered glass or powder coated sheet metal if you are looking for something more durable and don't want to replace the plywood.
Glass or metal would probably cost a bit more than I want to spend, considering I would have to get it cut to fit. It's definitely an idea for the future though.
I hadn't thought of neoprene or leather, and it's a great idea, thank you :)
My guess is that originally it would have been something that is good for under a piece of paper that you're writing on. Felt would have been too soft, the pen would punch through the paper. Leather or vinyl, backed with wood, would be perfect for that.
Neoprene wouldn't be a good choice if you're putting monitors on it - it compresses too much and the monitors would be unstable.
I wonder if you could get a sheet of plexiglass the right thickness - either a dark opaque or paint something thin to put under it.
The problem with neoprene is that it'll absorb dust, skin cells etc and you'll see a color change really fast. you want to wash a mouse pad every now and then and if its glued into your desk you wont be able to do that. Water will seep through into the wood below if you try and give it any kind of decent wash too.
The cheaper option that would still look great would probably be to find a big sheet of oak veneer for the desk top. If it were me though, I'd probably try and remove the plywood and install some oak if you want it to match, or maybe a darker wood like walnut if you want a little contrast
I didn't think of veneer, that's a good idea, thanks :)
I've just been looking at vinyl, but the shops here only seem to have the flooring patterns, so they're not doing it for me. I love the idea of replacing the plywood, but I'm trying to talk myself out of it before I get it wrong :D
An easier option might be thin oak faced plywood if there's enough of a rebate. Sheets of 4mm are pretty common and relatively inexpensive. It will be a lot easier to fit and stabilise than veneer.
So, not much of a woodworker myself but it looks like the top is in three panels? You could use that as an opportunity for contrast as mentioned above and make the whole project look like it has some design intentionality.
Maybe a darker maplewalnut veneer for that center panel as mentioned above and leather for the two smaller outer panels as mentioned elsewhere?
As it is an old desk, the inlay was most likely linoleum, which is similar to the PVC mostly used nowerdays for floors, but, however, is made from eco-friendly material.
Supposing you can find enough of it affordably, you could veneer the whole top. To make it interesting you could try cutting it and applying it in a geometric pattern if that's your thing.
I hear it can be a bit of a process. I’d recommend researching a fair amount before diving in. That said I’ve been waiting for the right project to do just that. Best of luck!