I literally ran into this myself recently replacing the SSD inside an old Chromebox.
I was literally unaware that it was an entirely different spec based on keying.
Further, it seems I can't find any reputable companies that make a SATA M.2 SSD in the 2242 size anymore. I can only find old Western Digitals that are more than double the cost of an equivalent NVMe simply because WD doesn't actually make SATA M.2s in that size anymore.
The only companies that make them in that size are all weird bogus never-heard-of-them-and-the-reviews-are-terrible.
No diss. I read that slot comment above you and went, "yep, yep, yep, makes sense. Man our standards are often dumb."
Laughed with joy at your comment, because I totally get how foreign this shit is to so many people. It's like if I walked up to a building engineer asking how they know that iron beam is safe for another 50 years via their skills and I'd just be like "......do what now?"
SATA is the interface that was mostly used until a few years ago, most people are used to seeing the version using cables (with an L shaped connector at both ends, still seen on 2.5" and 3.5" hard drives) but at some point they started making SATA drives using the m.2 form factor (with a connection similar to the one pictured in the OP) but the m.2 form factor is also used by other interfaces and not all of them are physically the same (the "expansion card" looks similar, the connection can be different), m.2 NVME drives are the ones mostly seen for storage space these days so most people assume that if storage is the m.2 type of will be NVME but sometimes (especially for laptops) it will be SATA that's required instead (like in OP's case)
Picture of an m.2 storage drive can be seen here and there's a keying section that shows the difference between B and M keys: https://en.m.wikipedia.org/wiki/M.2
They said the b SATA m2 SSD key NVMe AFR actuator clusters the cache in m.2 U.2 mSATA PCIe made a SATA lata gata when she said 2.5" wasn't big enough but 3.5" was too much and LBA LP MTTR spindles the motor with 28 pins when it lost a pin while bowling for transfer rate cause you failed to defragment your USB-connected PCIe Gen 4 pokemon with AHCI finding IOPs over 9000 so the HDD Teraflopped into the EDSFF pool and RAMmed itself 6 feet under.
SATA= Slow (Max 6 Gbps)
PCIe = Fast (Max > 100 Gbps in theory)
This is the maximum rate from the drive to the motherboard. Many drives are fast enough that SATA works become the bottleneck. With PCIe, the drive can run at its full speed, whatever that may be.
Another thing to watch out for is single-sided vs double-sided. Many laptops have flush mounted m.2 slots that won't fit an SSD with chips on both sides of the board.
Story of my past couple months. There are five different products named "g4 dock", four of which are newer than the G5 dock.
The OLD g4 dock, and then 120W/280W Thunderbolt variants that are either TAA approved or not. One of these four has a 2.5GB Intel NIC. Good luck figuring out which one because they merged the specsheet for all four of them.
possily running into b vs m key situation. if you have a laptop that was made during the transition period of sata based m.2 to pci-e based ones, knowing which key you needed is important.
I'm confused, that looks like an m.2 slot, and it's not like it could really be anything else. Msata is a dead standard and looks quite different. The slot would be too wide.
Whoa I had no idea about this. Just put an m2 nvme in my refurbished 2017 HP elitedesk and didn't even know to check for sata vs nvme. I thought they were all nvme.