Klipper vs Marlin
Klipper vs Marlin
I actually have Marlin + Octoprint but found out recently that Klipper exist. I read everywhere that Klipper is better but I don't really get why. I understand that Klipper use raspberry as powerfull calculator instead of the STM32 of the printer, but octoprint is used to send Gcode to Marlin too... So what's the really difference please?
Edit : I don't understand how Klipper or Marlin can give better results when gcode and instructions are generated by Cura
I was once at the exact same point where you are now. Marlin+octoprint really is good enough for most cases once you're up and running.
I pulled the trigger for klipper a couple of years ago and honestly never looked back. Mainsail is just so much more refined and usable than octoprint. Tuning Firmware Settings in klipper is so much simpler than marlin, it's just a breeze.
Combined with modern controller board (f.e. mks skipr), modern drivers like TMC2209, sensorless homing, Canbus-toolhead, resonance measuring, mmmh... chef's kiss ;)
I'll try it today then!
So both Klipper and Marlin+Octoprint use a Pi and an arduino (in simplified versions, the SBC and the MCU can be any boards but I’ll use those brand names to make it easy).
Marlin uses the Pi to display the web interface, then sends the gcode to the arduino. Then the arduino does the math to convert the gcode to motor commands. Gcode.
Klipper uses the pi to display the web interface, but it also takes the gcode and converts it to motor commands in the pi and only sends those simplified motor commands to the arduino.
So with Klipper the arduino doesn’t need to convert gcode which is a pretty intense computation. Also, gcode is actually pretty heavy to send vu serial over usb in Marlin and often the printer can print faster than the gcode can be sent. Which results in hang ups in the print, the printer pauses, especially in a print with a lot of curves and printing fast. Klipper can use the full power of the pi to make intricate motor commands, fine tuning acceleration and all to avoid vibrations (input shaper, it even uses an accelerometer sensor to refuse vibrations making cleaner prints and quieter printing)
Other benefits of Klipper, settings don’t need to be flashed to the arduino, they are saved in a text file on the pi. Changing Config is a simple text edit, then reboot to apply the changes. You can edit the settings right in the web interface.
One of the down sides of Klipper was that you had more functions in Octoprint with plugins, that’s not true anymore. You have many plugins compatible with Klipper with Timelapse exclude area, remote access, Obico (the spaghetti detective), and so on.
The web interface is much lighter and responsive than the bulky Octoprint. Octoprint was an afterthought while Mainsail was purpose designed for Klipper.
I used to run Marlin and Octo and hated the experience. Since I tried Klipper I can’t go back.
Thank you for the explanation!
You’re welcome. There is a lot more than that even. When you start digging through, Klipper allows you so much control. You can even have your printer run shell commands (deactivated by default because it so powerful, it can be dangerous if you don’t know what you’re doing)
You can control RGB LEDs and more. You can also connect many arduino isntesad of just one
One slight correction, nothing is stopping you from using Klipper with Octoprint. You just need to install the Octoklipper plug-in to Octoprint. Most people who run Klipper choose to use Mainsail or Fluidd, but it's not required.
You can but it doesn’t mean you should. The way Octoprint manages interacting with the printer is it spoon feeds g-code lines one by one. So it can stop sending them to pause a print, change the values to change Z height for instance etc… however, Klipper is usually able to print faster than Octoprint an send gcode via serial. The crutch is to use VirtualSD mode in Klipper but then Octoprint has very limited interaction with the gcode other than start stop, no gcode modification possible. Enters Moonraker. Moonraker is an API that allows to interface with Klipper in a standardized way to send complex commands to the printer. Mainsail UI is using it, so is Fluidd, KlipperScreen, Telegram bot etc…. The benefit is that Moonraker commands Klipper to do the changes natively instead of adding a layer to the chain. So yeah you can use it, but there is no real incentive to do so now that Moonraker is here. 5 years ago Octoprint was the only way to control Klipper and it was just painful, but we had no alternative.
Always be careful about the new thing. People tend to overhype the new thing and downplay the old thing. Klipper is neat! I've seen it do good stuff. However, Marlin is still good. Nothing wrong with it, either.
Klipper is great... Once you get it working. Way better than Marlin, but good luck getting it to work.
I swapped my motherboard for a BTT Manta + CB1 + EZ2209 drivers. Took about 7 months to get it to a state where my prints are regularly okay. Every 3D printing community I've come across is less than helpful, and all Klipper documentation is written like you're already at a pro level, as does pretty much every other guide out there. People will swear it's so easy, but you know what helped after 7 months of tinkering? Myself just throwing everything I have at my config in hopes of something working.
What kind of printer do you have?
Klipper in a frequently used application like Voron? You'll have help for days. Klipper in an novel or bespoke application? It's going to be quite a a bit harder.
I have an Ender 6, which is a super common printer. Not on the same level as the 3.
Voron isn't an application, though. It's a type of printer.
Novel or bespoke printer? Not sure what you're talking about, but it's supposed to be universal firmware. There are plenty of guides out there and folks running Klipper on all sorts of printers, including mine. They just aren't well-written, or aren't written for beginners, or assume you're a pro that doesn't need anything explained.
This is exactly what I'm talking about with the 3D printer community. I'll say one thing, and then someone will say something completely unrelated in response, like you just did.
I ask, "Hey, can anyone with (insert my specs here) show me their Klipper config or Slicer profiles for reference?" and I get 100 responses asking me why I'm using the hardware I'm using, recommending me other hardware that they like, telling me to use a different slicer that they like better, telling me if I don't tell them my issue or show them pics of my prints they can't help me (I never asked for help with prints, just to look at someone's config with similar hardware), downvoting me for not already being a 3D printing pro, and just generally being unpleasant and literally answering anything but my question.
I work in tech. I'm used to Googling answers, hitting up forums, digging through old posts, etc. It's about 50% of how I get my job done. There is something fundamentally wrong with the majority of the 3D printing community.
Not bashing this community specifically, as it's too new to judge and so far people seem helpful and nice, but this is a problem I run into everywhere I turn to for assistance, like GitHub, Reddit, Printables, and various other manufacturer forums. The 3D printing community is pretty dogshit.
Let's make this a much better community than literally everywhere else (which shouldn't be difficult at all). When you post your setup, post your full specs with your firmware config and slicer settings. Is there a way we can tag ourselves or add a profile/signature? Maybe we can even put links to our specs.
So much of the 3D printing community seems to want to kill it by scaring off all newcomers. We can make this place the definitive stop for 3D printing knowledge, questions, and configs, but it's going to take the work of some mods and the entire community to get there.
Share knowledge like the rest of the tech enthusiast world. Your Klipper config isn't some super secret proprietary code for your eyes only. You don't have to guard it like it's your virginity. This hobby is going to die outside of super corporate builds with zero after market parts or builds like the Bambu X1 if the 3D printing community as a whole doesn't learn how to share and not be a dick.
gcode only contains high level instructions, e.g. "move 10mm on the X axis", which the firmware has to convert this to electrical pulses that can be sent to the stepper motors. If this is done naively the hardware wouldn't be able to follow the instructions due to inertia, filament viscosity, etc. Both firmwares have several methods to deal with this, but afaik Marlin does not have anything that does the same as Klipper's input shaper. Marlin has "linear advance" while Klipper has "pressure advance" which both try to solve the same problem but have different algorithms and you calibrate them differently. Using Klipper with calibrated input shaper will probably allow you to print faster than Marlin at an equivalent quality level.
Another difference is that all Klipper configuration goes into a text file, and you just restart Klipper to reload it. To change some settings i Marlin you have to re-compile the entire firmware and flash it.
Marlin's G29 command has different syntax depending on which ABL algorithm the firmware was compiled with, which IMO makes it more difficult to help other people who didn't compile their own firmware (i.e. who don't know which ABL algorithm their Marlin has).
Thank you for the explanation!
Found out just now that Marlin finally got input shaping: https://marlinfw.org/docs/gcode/M593.html
There's however a risk that you have to compile your own firmware if you want to enable it. Definitely not impossible if you know your way around computers, but editing Marlin configs can be quite daunting. Not that installing and configuring Klipper would be trivial for a computer illiterate person, but over all I've found it much easier to work with. I used Marlin for about a year, including compiling my own version of it, before switching.
For me the biggest disadvantage with Klipper is that I haven't got around to printing an enclosure for the RPi so it's just sitting on the desk next to the printer, and it's not compatible with the E3v2 display so I have to use Mainsail on my phone if I want to control the printer from the same room. I could of course buy a proper touch screen and run KlipperScreen, but they're a bit pricey.
They are both good!
I believe they both have pressure advance and resonance compensation. With klipper you get option for much better UI (Mainsail OS in my case) and you can change your config in a web browser.
Well I said much better UI, but its subjective.
Also, I think you can use octoprint with klipper fw, but never tried that. Mainsail+klipper is my vote
The best part of klipper for me is being able to change pretty much any setting in a text file and restart and it works without having to screw around with SD cards, or firmware filenames, or compiling other than the first time.
For me the responsivity of Klipper UI was reason enough. Octoprint is unbelievably slow on the same hardware. The other thing was ease of configuration - no firmware compilation and flashing necessary. And the third is the actual printing performance - Octoprint has a really bad implementation of the actual print data transfer, and the serial interface routinely chokes on fine data such as arcs. That never happens with Klipper, even at much, much higher print speeds.
This might be situation dependant, but I personally (Ender 3 S1 Pro) spent weeks searching for ready-made firmware, then learning how to modify and compile firmware, then troubleshooting why I couldn't get Linear Advance working, only to finally figure out that it just plain wasn't supported by Marlin on my hardware.
I was about to give up and just go back to the stock Creality firmware, but decided to give Klipper a go without really knowing the full capabilities, other than that it natively supported Pressure Advance. In a fraction of the time I had spent dicking around trying to get a single feature enabled in Marlin, I had my printer running off a slick web interface, fully tuned up and printing substantially better than I was able to achieve with Marlin.
Now, granted, I never tried to get up and running with Octoprint so I probably am only half answering your question, but as a relatively casual printer I have found using and tweaking Klipper to be substantially more straightforward, and would not hesitate to recommend giving it a stab as long as you have a RPi laying around already.
Yes one of the big advantages of klipper is that you don't need to recompile the whole thing to make changes to your configuration. You just edit it in a text editor and then save and restart the firmware.
I also haven't used Octoprint, but other advantages for klipper over marlin are the ability to control your printer via a webUI, pressure advance, resonance compensation, easily add cameras, mesh leveling visualization, and a bunch more that I'm forgetting off the top of my head.
I did exactly the same thing as you. I like the built in web management in klipper so much more than octoprint.
There is post processing g code manipulation. Abl works this way, as does arc welder. If your bed is high on one spot there has to be some sort of manipulation after cura.