The things you find when you go looking...
The things you find when you go looking...
So that's why a 2 systems were getting crappy speeds. Yes, 2. It had been used only to split a single drop from another switch between two systems.
New drop, happy clients.
Some stuff here is museum material.
You're viewing a single thread.
As someone who grew up with 10Base2 and 10BaseT, and thought 100Mbps was amazing - it still surprises me every time I'm reminded how slow it is now. I buried a cat6 cable out to my wife's studio and due to (I assume) some grounding issues it only syncs at 100Mbps - it works for general browsing etc., but every time we try to move some data it's arggghhh.
Shouldn’t be a grounding issue as you said that you buried it.
Can't find an emoji holding its side and laughing. Just pretend.
It's a 200' cable and the buildings each have their own connection to the power company. I suspect that the earth potential of the two buildings is quite different - I just have not figured out a way to measure it yet and not sure if there's anything I can do to fix it even if I do confirm it.
That shouldn't be a problem unless you're using grounded shielded cable, in which case you should make sure the shield ground is only connected at one end.
Potentially I might know a Gaia that can help.
a Gaia?
Pull a copper wire from one ground to the other?
I guess that's what I haven't figured out yet - it's about 200' and I don't have 200' of wire laying around. I'm thinking of making dummy terminations for each end of my cat6 cable and stripping each of the pairs and twisting them together so it works as a single conductor and using that to measure.
[I am not an electrician, so this is not a recommendation and I would not be qualified to make one] With that out if the way, what I would do to test this theory is to measure the voltage between a ground pin in each house, using am extension cord or similar to bridge the distance. A decent multimeter should do the job. Note that the cord itself would cause a voltage drop, but the ethernet cable would too so I think that'd if you can't measure a difference with the extension cord (which should have less ressistance than the ethernet one) then it shouldn't matter(?)
Note that while ground is normally "the safe pin" (not really a thing I guess but..) in this case, where the suspicion is a differential, then it should be very much considered live. And that means all precautions should be taken, such as not following a random stranger's advice.
It might be worth looking into those plugin-sockets with ground fault protection in both ends (not sure if they'd do anything in this case), if the ethernet cable is shielded, maybe removing the shield in one end (such that the cable is grounded only to one house) could make things better (or maybe even worse?),
and while maybe not feasible: fiber wouldn't be affected by this as it's just light, and likewise WiFi or other wireless tech could be feasible. with clear line of sight, 5GHz can provide very good speed and latency.
The phone lines repurposed as ethernet in my parents’ house also only do 100 Mb/s. I concur, so painful. I want to put a storage server there but no matter where it’s limited by awful speeds. It also means getting faster internet would be useless because it would be limited by these wires.
I've worked at places where we repurposed old CAT3 cables for network connecting printers, desk phones, environmental sensors, etc. Rare occasions where 10Mbps works just fine. Using that to connect a PC would suck.
I wonder if it would have been the same cost to do an outdoor fiber run.
Probably not, the costs were essentially just sticking ethernet ports on the walls next to the phone ports and rewiring the existing wires to those ports. And back when this was done (whenever we got DSL, around 2005 maybe?) fiber tech was probably prohibitively expensive. I haven’t looked up how much fiber modems cost but it would probably be more expensive even today.
Fast ethernet ain’t so fast these days
What type of cable did you use? Water could have seeped into which cause a bunch of weird issue because the resistance on the wires goes all wonky. I’m not sure if you have access to a cable certified like a Fluke, but if you do I would use that to test and it will most likely tell you your issue. I highly doubt it’s a grounding issue because you’d issues like that in large buildings where the power is on different phases or technical power.
It's pre terminated pure copper direct burial cat6 from Amazon. I don't have access to a real tester, but my cisco switch has some built in test capability and I'm not sure I fully understand the results, but it's assessment of the cable length is pretty close and, more importantly, it shows all the pairs are the same as each other. I think that if there was some damage to the cable, it's unlikely that it would affect all the pairs in exactly the same way. I have other weird grounding issues - like 20V between neutral and ground, even though it's a new house and they're properly bonded at the service entry. I had a really old transformer on the street feeding the two buildings and the power company recently replaced it - I was disappointed when this didn't resolve all my issues.